How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
This post below pertaining to Installing A Bathtub is seriously informative. Don't miss it.
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough task. If the old bathtub is easily available, the project can relocate easily; if you need to open up a wall to remove the old tub and place the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also set in the new one. See to it you have qualified yourself for the work and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed task, it is far better to take into consideration employing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This post will help you mount a new bathtub in your washroom if you have already acquired a brand-new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your devices and product checklist must comprise the following:
Planning for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to stop strain on the bath tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather troublesome as a result of the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bath tub
Making use of both wood boards under its feet, put the bathtub in the required position. The wooden boards are helpful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bath tub till the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Activate the supply of water and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait until the bath tub has been used a minimum of once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, causing difficulties with wetness and feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to enable the motion experienced when the tub is in usage. The sealer can crack fairly early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I ran across that entry on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a search on the search engines. Do you know about somebody who is intrigued by the subject? Please feel free to share it. Kudos for your time. Visit again soon.
Schedule Today! Report this page